Aerospace Engineering + Physics
Make a model wind tunnel and test shapes
Build a small wind tunnel from a fan and straws and compare the drag of different shapes.
- Intermediate
- 1–2 weeks
- 500–1,000
606 projects · 13 streams · every class
Engineering projects 20
Design, build and test projects for every engineering branch, from mini projects to final-year capstones, with low-cost versions where possible.
20 Engineering projects
We couldn't find an exact match. These are the closest 20, found by leaving out the class.
Or look inMechanical EngineeringCivil EngineeringElectrical EngineeringElectronics and CommunicationChemical EngineeringAll EngineeringTwo-subject projectsHelp me choose
Civil Engineering · Structural Analysis
Compare the strength of beam cross-sections
Fold the same sheet of card into flat, tube, box and I shapes and measure how much each bends.
- Intermediate
- 2–7 days
- Under 250
Civil Engineering + Earth Science
Design an earthquake-resistant building model
Build a simple shake table and test how bracing and base isolation protect a model tower.
- Intermediate
- 1–2 weeks
- 250–500
Mechatronics and Robotics + Agricultural Technology
Automate a greenhouse model
Control a fan, a pump and a light in a model greenhouse from temperature, moisture and light readings.
- Intermediate
- 2–4 weeks
- 1,000–2,500
Materials, Energy and Other Branches + Environmental Science
Build a biogas digester model
Ferment kitchen waste in a sealed bottle and measure the gas collected over a month.
- Intermediate
- 2–4 weeks
- 250–500
Civil Engineering + Robotics, IoT and Hardware
Build a model of a smart street light
Make street lights that switch on at dusk and brighten only when a vehicle passes.
- Intermediate
- 1–2 weeks
- 500–1,000
Mechanical Engineering · Machines
Design a gearbox and measure its speed ratios
Build a two-stage gear train and check the measured ratio against the tooth counts.
- Intermediate
- 1–2 weeks
- 250–500
Electrical Engineering + Physics
Build a wireless power transfer demo
Light an LED with no wire connection using two coils and an oscillator.
- Intermediate
- 2–7 days
- 250–500
Industrial and Manufacturing · 3D Printing
Optimise a 3D print for strength and time
Print test bars with different infill and layer settings and find the best strength per minute.
- Intermediate
- 1–2 weeks
- 500–1,000
Electrical Engineering · Power Systems
Model a power grid with series and parallel loads
Show why power is transmitted at high voltage using long thin wires and small bulbs.
- Intermediate
- 2–7 days
- 500–1,000
Materials, Energy and Other Branches · Materials Testing
Test materials for strength with a home-made rig
Stretch wires and strips of different materials to breaking and compare their strength.
- Intermediate
- 1–2 weeks
- 250–500
Mechanical Engineering · Fluid Systems
Build a model of a gear pump or centrifugal pump
Make a small centrifugal pump from a motor and a bottle cap and measure its flow at different heights.
- Intermediate
- 1–2 weeks
- 500–1,000
Chemical Engineering · Separation
Build a distillation column model
Separate coloured water from a salt solution by simple distillation and measure the recovery.
- Intermediate
- 1–2 weeks
- 250–500
Electronics and Communication · Communication Systems
Build an FM radio receiver
Assemble an FM receiver from a radio IC and tune in local stations.
- Intermediate
- 1–2 weeks
- 500–1,000
Mechanical Engineering + Environmental Science
Build a solar water heater
Make a flat-plate collector from black tubing and measure how much heat it captures.
- Intermediate
- 1–2 weeks
- 500–1,000
Materials, Energy and Other Branches + Chemistry
Study corrosion protection for steel
Compare paint, oil, zinc coating and sacrificial protection on steel in salt water.
- Intermediate
- 2–4 weeks
- 250–500
Electrical Engineering + Environmental Science
Generate electricity from a bicycle
Couple a DC motor to a bicycle wheel and measure the power a person can produce.
- Intermediate
- 1–2 weeks
- 1,000–2,500
Aerospace Engineering + Physics
Measure the thrust of a water rocket
Build a static test stand and measure thrust against time for different water fills.
- Intermediate
- 1–2 weeks
- 250–500
Electrical Engineering · Generators
Make a hand-crank emergency torch
Build a torch that stores hand-cranked energy in a capacitor and lights an LED.
- Intermediate
- 1–2 weeks
- 500–1,000
Biomedical Engineering · Biomechanics
Build a prosthetic hand model
Make a string-tendon hand from card and straws that grips objects.
- Intermediate
- 1–2 weeks
- 250–500
0 to compare
Compare